espcom_sync_failed [ERROR Solved]

If you are using ESP8266 and Facing One of the most common errors with the ESP8266 is the “espcom_sync_failed“. You can find solution in this article.

espcom_sync_failed [ERROR Solved]

If you receive this error when the RST is not set to GND. To correct this error, please verify:

1. if the jumper wire correctly connected and use the above Pinout table;
2. confirm that the Arduino RST is set to GND;
3. confirm that the board: Generic ESP8266 Module is selected in the Arduino IDE. or Select correct board that you are use.

Your espcom_sync_failed error solved.

Setting up Arduino IDE for ESP8266/NodeMCU

Visit this : Arduino Support for ESP8266 with simple test code

What is ESP8266?

The ESP8266 series, or family, of Wi-Fi chips is produced by Espressif Systems, a fabless semiconductor company operating out of Shanghai, China. The ESP8266 series presently includes the ESP8266EX and ESP8285 chips.

ESP8266EX (simply referred to as ESP8266) is a system-on-chip (SoC) which integrates a 32-bit Tensilica microcontroller, standard digital peripheral interfaces, antenna switches, RF balun, power amplifier, low noise receive amplifier, filters and power management modules into a small package. It provides capabilities for 2.4 GHz Wi-Fi (802.11 b/g/n, supporting WPA/WPA2), general-purpose input/output (16 GPIO), Inter-Integrated Circuit (I²C), analog-to-digital conversion (10-bit ADC), Serial Peripheral Interface (SPI), I²S interfaces with DMA (sharing pins with GPIO), UART (on dedicated pins, plus a transmit-only UART can be enabled on GPIO2), and pulse-width modulation (PWM). The processor core, called “L106” by Espressif, is based on Tensilica’s Diamond Standard 106Micro 32-bit processor controller core and runs at 80 MHz (or overclocked to 160 MHz). It has a 64 KiB boot ROM, 32 KiB instruction RAM, and 80 KiB user data RAM. (Also, 32  KiB instruction cache RAM and 16 KiB ETS system data RAM.) External flash memory can be accessed through SPI. The silicon chip itself is housed within a 5 mm × 5 mm Quad Flat No-Leads package with 33 connection pads — 8 pads along each side and one large thermal/ground pad in the center.  Read about For Overview, Datasheet, Technical Reference. ESP8285 is a variation of ESP8266 with 1 MiB of embedded flash memory.

The Modules

Vendors have consequently created a multitude of compact printed circuit board modules based around the ESP8266 chip. Some of these modules have specific identifiers, including monikers such as “ESP-WROOM-02” and and “ESP-01” through “ESP-14”; while other modules might be ill-labeled and merely referred to by a general description — e.g., “ESP8266 Wireless Transceiver.” ESP8266-based modules have demonstrated themselves as a capable, low-cost, networkable foundation for facilitating end-point IoT developments. Espressif’s official modules are presently ESP-WROOM-02 and ESP-WROOM-S2.

• Espressif Systems
• Ai-Thinker
• DOIT
• Wireless-Tag Technology

Recommended:

• Logical Design of IoT | IoT Communication Models & APIs
• Best Internet of things Platforms for building IoT projects
• Industrial IoT | Industry 4.0 | IIoT | Industrial Internet of Things
• Home automation | Internet of things Products for Home Automation
• Industry 4.0 — the Industrial Internet of Things (IIoT)?
• Internet of things Enabling Technologies
• Government Applications in Internet of things
• Internet of things Operating Systems
• Role of Internet of things in Smart City
• What is Cellular Internet of things?
• Internet of things Gateway
• Internet of things Data Protocols
• Wireless Internet of things Network Protocols